Tuscaloosa Window Pros provides professional bay and bow windows in Tuscaloosa, AL for residential and commercial properties across Tuscaloosa County and the Black Warrior valley. This is the page where we most often talk people out of what they came for. On a brick-veneer wall, cutting in a new bay or bow is an expensive structural job dressed up as a window purchase.
Here is what it actually involves. The masonry opening has to be widened, which means removing veneer and setting a longer steel lintel with proper bearing at each end. The framing behind it has to be opened and headed. The unit then projects past the plane of the brick, so it needs support back into the floor structure, its own small roof, flashing where that roof meets the veneer, and insulation in the projection.
Every one of those is a place water gets in. In our experience the leaks that turn up in a bay are almost never the window. They are the roof-to-wall flashing, the counterflashing at the veneer, or a seat board with no drainage under it. That is not an argument against bays. It is an argument against buying one as if it were a window.
So on brick veneer our first proposal is usually different. A mulled assembly in the existing masonry opening, a fixed picture lite flanked by two operating units, gives you the light and the ventilation that people actually want from a bay, in a flat plane, with no roof and no cantilever. It costs a fraction of the money and there is nothing above it to fail.
If you want the projection, we will build it, and we will price it honestly, including the masonry and the roofing. We would rather lose the job at the estimate than have you discover the lintel line halfway through. A bay is a lovely thing in the right house and it should be bought with the whole number in front of you.
Replacing an existing bay is a different and much better proposition. The structure, the roof and the support are already there. We assess the head and seat framing for rot, replace the units in the existing box, rebuild the seat and ceiling insulation, and re-flash the roof junction. That is a real job with a real result and none of the structural cost.
Bows behave the same way with more joints. Four or five narrow units curve out on a shallow radius, which means more mull joints to seal and a wider roof to flash. On the newer clad walls both are considerably easier, because the cladding comes off and the flashing can be lapped into the wall properly rather than reglet-cut into mortar.
We will always show you the flat mulled alternative next to the projecting one, with both prices, before you commit to either. Most people who came in wanting a bay end up buying the mulled assembly, and the ones who still want the bay buy it knowing what it is.
Our licensed and insured team brings the right materials and equipment to every job — brick veneer built up around the original window frame, brick mould casing bedded into the mortar joint at the head, steel lintel angles carrying the veneer over each masonry opening, integral nailing flanges lapped over the weather-resistive barrier, pocket inserts anchored into the surviving jamb rather than the framing, sloped sill pans with end dams under full-frame units — and backs the work with a written workmanship warranty. We serve Tuscaloosa and nearby communities including Northport, Holt, Cottondale, Brookwood.
What We Handle
Everything our bay and bow windows in Tuscaloosa covers
One crew, one point of contact, and the full range of bay and bow windows work in Tuscaloosa, AL. If it is on this list we do it in house rather than handing it to a subcontractor:
- bay windows Tuscaloosa
- bow windows Alabama
- garden window replacement
- bay window support brackets
- bay window roof and flashing
- angled bay window
- bay window seat
- bow window five lite
- bay window installation cost
- replacing an existing bay window
- mulled picture window assembly
- bay window head lintel
- bay window insulation
- bay window cladding
- bay window for brick homes
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Tuscaloosa services.
Materials, equipment and how we do bay and bow windows
The difference between bay and bow windows that lasts and bay and bow windows that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with brick veneer built up around the original window frame, brick mould casing bedded into the mortar joint at the head, steel lintel angles carrying the veneer over each masonry opening, integral nailing flanges lapped over the weather-resistive barrier, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Tuscaloosa job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of window work in Tuscaloosa County and the Black Warrior valley means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do bay and bow windows outside Tuscaloosa
Tuscaloosa Window Pros covers Tuscaloosa and the surrounding communities of Tuscaloosa County and the Black Warrior valley. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Bay and Bow Windows in Northport, AL — Tuscaloosa County, population 31,125
- Bay and Bow Windows in Holt, AL — Tuscaloosa County, population 3,413
- Bay and Bow Windows in Cottondale, AL — Tuscaloosa County, population 3,130
- Bay and Bow Windows in Brookwood, AL — Tuscaloosa County, population 2,504
- Bay and Bow Windows in Coaling, AL — Tuscaloosa County, population 2,035
- Bay and Bow Windows in Coker, AL — Tuscaloosa County, population 904
Start on the Tuscaloosa Window Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Tuscaloosa Chooses Tuscaloosa Window Pros
- ✓We read the outside of the wall before the inside of the window, because a brick-veneer opening and a flanged clad-wall opening are two different jobs at two different prices
- ✓Every proposal states whether the unit is a pocket insert or a full-frame replacement, and how much glass width you give up to get the cheaper one
- ✓We will not cut a brick veneer to sell you a bigger opening when the existing masonry opening can carry the window you actually need
- ✓On clad walls we re-lap self-adhered flashing over the nailing fin in sequence, rather than running a bead of sealant around the perimeter and calling it flashed
The standards behind bay and bow windows
Quality here is not a matter of opinion — it is written down. The bay and bow windows work we do in Tuscaloosa follows published industry standards: NFRC sets the U-factor and SHGC ratings on every window label, and ENERGY STAR defines the efficiency thresholds by climate zone. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every bay and bow windows project in Tuscaloosa gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free bay and bow windows free estimate in Tuscaloosa, or request a quote and we'll get right back to you.